Smart Cutter CX
Smart Cutter CX is designed for cutting PE, EPE, XLPE, EVA and PU planks or rolls to the desired size in a matter of seconds. The CX uses a sliding slit blade to make the cross cuts rather than the chop blade. Work with ¼” to 3.5” (Thickness) x 3.5” – 51” (Width) x 2” or larger (Length)
Smart Cutter CXD is an advanced solution including all feature from CX, also offering the capability of partial cutting to Foam and honeycomb. Work with ¼” to 3.5” (Thickness) x 1.75” – 51” (Width) x 2” or larger (Length)
| SC-6004CX | SC-6004CXD | |||
|---|---|---|---|---|
| Max. material width(1) | mm Inch | 1350 53 | 1350 53 | |
| Max. cutting width (2) | mm Inch | 1295 51 | 1295 51 | |
| Overall dimensions w/ conveyor | mm Inch | 7112 x 2920 x 1700 280 x 115 x 67 | 7802 x 4509 x 1991 307 x 178 x 78 | |
| Weight | kg lbs. | 2800 6100 | 4500 9900 | |
| Feeding speed (3) | mm/s Inch/s | 350 13 | 350 13 | |
| No. of circular blades (4) | 8 | 16 | ||
| Cross cut type | Circular | Circular | ||
| Compressed air requirement | 90 - 100 psi | 90 - 100 psi | ||
| Electrical requirements (5) | 480V, 3PH, 4Wires AWG8, 50/60HZ | 480V, 3PH, 4Wires AWG8, 50/60HZ | ||
| Electrical power capacity | 15KW | 18.5KW | ||
| Recommended material(6) | PE, XLPE, PU, Honeycomb | PE, XLPE, PU, Honeycomb | ||
| Operator safety | All blades are contained inside of the machine housing and an operator safety cage is located at the exit point (exiting conveyor option available). | |||
| Machine Capability | Cutter C | Cutter CX | Cutter CXD | ||||
|---|---|---|---|---|---|---|---|
| Density Pcf | Material Thickness(Nom) Inch | Min. Slitting Width Inch | Cross Cut Tolerance Inch | ||||
| PE | ≤1.7 | [3 - 3.5] | 8 | ±1/8 | Y | Y | Y |
| [2.5 - 3] | 6 | ±1/8 | |||||
| [2 - 2.5] | 4 | ±1/8 | |||||
| [0.5 - 2] | 3.5 | ±1/8 | |||||
| 2.2 | [3 - 3.5] | 16 | ±1/8 | ||||
| [2.5 - 3] | 8 | ±1/8 | |||||
| [2 - 2.5] | 6 | ±1/8 | |||||
| [0.5 - 2] | 3.5 | ±1/8 | |||||
| 4 | [1.5 - 2] | 10 | ±1/8 | ||||
| [0.5 - 1.5] | 8 | ±1/8 | |||||
| 6 | [0.5 - 1] | 6 | ±1/8 | ||||
| EVA / XLPE | ≤2.2 | [1 - 2] | 8 | ±1/8 | N/A | Y | Y |
| [0.5 - 1] | 3.5 | ±1/8 | |||||
| 4 | [0.5 - 1] | 8 | ±1/8 | ||||
| 6 | 0.5 | 8 | ±1/8 | ||||
| PU | Case by case results - SFM will test your material upon request(7) | N/A | Y | Y | |||
| Honeycomb | Case by case results - SFM will test your material upon request(7) | N/A | Y | Y | |||
| (1) (2) Max. cutting width and thickness are material dependent. Measured with 1.7 PCF extruded PE cushion. | |||||||
| (3) Material dependent. Measured with 2" thick, 1.7 PCF extruded PE . | |||||||
| (4) Circular blades used for slitting. | |||||||
| (5) This is the standard electricity configuration. Can be customized for your machine. | |||||||
| (6) Cutter CX is not able cut soft PU(Less than 30ILD). Send samples to SFM to verify before ordering. | |||||||
| (7) Due to each manufacturer might using different grade of paper- Send samples to SFM to verify before ordering. | |||||||
